D-Link KX-TDA100 Bedienungsanleitung Seite 235
- Seite / 250
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4.1 Troubleshooting
Installation Manual 235
202* LPR start up error
(No Program)
• Optional service card
malfunction: DHLC, DLC,
CSIF, T1, E1, BRI, PRI,
OPB3, CTI-LINK, E&M,
IP-GW, DID, SLC8
• Pull out and re-insert the
corresponding optional service card
• Press the Reset Button
• Update the software of the
corresponding optional service card
• Replace the corresponding optional
service card
203* LPR start up error
(Version NG)
204* LPR start up error
(Download NG)
205* LPR start up error
(No response)
206 LPR start up error
(Card type NG)
207 LPR start up error
(Check SUM NG)
230* Card disconnected • Optional service card not
installed properly
• Optional service card
malfunction
• Back board malfunction
• See if the corresponding optional
service card is installed properly
• Pull out and re-insert the
corresponding optional service card
• Press the Reset Button
• Replace the corresponding optional
service card
• Replace the back board (be sure to
turn off the Hybrid IP-PBX when
replacing)
231 LPR alive check error • Optional service card
malfunction: DHLC, DLC,
CSIF, T1, E1, BRI, PRI,
OPB3, CTI-LINK, E&M,
IP-GW, DID, SLC8
• Back board malfunction
• MPR card malfunction
• See if the corresponding optional
service card is installed properly
• Pull out and re-insert the
corresponding optional service card
• Press the Reset Button
• Replace the corresponding optional
service card
• Replace the back board (be sure to
turn off the Hybrid IP-PBX when
replacing)
• Replace the MPR card (be sure to turn
off the Hybrid IP-PBX when replacing)
232 MPR-LPR
communication error
233 LPR data check error
234 DPLL clock failure
235* CS clock failure • Optional service card
malfunction: CSIF
• Replace the corresponding optional
service card
250* T1/E1 DSP failure • Optional service card
malfunction: T1, E1
• See if the corresponding optional
service card is installed properly
• Replace the corresponding optional
service card
251 MSG DSP failure • Optional service card
malfunction: MSG
Error Code Error Message PROBABLE CAUSE SOLUTION
- KX-TDA100 1
- KX-TDA200 1
- Installation Manual 1
- System Components 2
- Installation Manual 3 3
- 4 Installation Manual 4
- T7565) series telephones 4
- Important Safety Instructions 5
- SAVE THESE INSTRUCTIONS 6
- Precaution 7
- MODEL No.: 8
- SERIAL No.: 8
- Installation Manual 9 9
- Introduction 10
- Installation Manual 11 11
- 12 Installation Manual 12
- Table of Contents 13
- 14 Installation Manual 14
- Installation Manual 15 15
- 16 Installation Manual 16
- Section 1 17
- System Outline 17
- 1.1 System Highlights 18
- PC Phone/PC Console Features 19
- Hospitality Features 19
- 1.2 Basic System Construction 20
- Hybrid IP-PBX 21
- Mountable Equipment 22
- 1.3 Options 24
- 1.4 Specifications 27
- 1.4.2 Characteristics 29
- 1.4.3 System Capacity 30
- Maximum Terminal Equipment 33
- MEC Card Calculation 33
- Power Supply Unit Selection 34
- PSU Capability 35
- Section 2 37
- Installation 37
- 2.1 Before Installation 38
- 2.2.1 Unpacking 40
- 2.2.2 Names and Locations 41
- Opening the Front Cover 42
- Closing the Front Cover 43
- Function 44
- Guide Rail 45
- Release Lever 46
- Back Board 46
- 4. Replace the PSU 47
- 2.2.5 Frame Earth Connection 48
- Installation Manual 49 49
- Covering the Blank Slots 52
- Handling of the Cables 53
- 2.2.8 Types of Connectors 55
- 56 Installation Manual 56
- When connecting a BRI card 57
- 58 Installation Manual 58
- Installation Manual 59 59
- 60 Installation Manual 60
- Anchor Plug 61
- Screw (B) 62
- Screw (A) Metal Bracket 65
- Screws (B) 66
- Metal Bracket 66
- Installation Manual 67 67
- Overview 68
- Outside Installation 69
- Installation of an Earth Rod 69
- 70 Installation Manual 70
- 2.3.1 MPR Card 71
- 2.3.2 MEC Card 73
- 2.3.3 RMT Card 74
- 2.4.2 DID8 Card 77
- 2.4.3 CID/PAY8 Card 79
- 2.4.4 CID8 Card 80
- 2.4.5 E&M8 Card 81
- 2.4.6 T1 Card 84
- 2.4.7 E1 Card 87
- Switch Settings 88
- 2.4.8 BRI4 and BRI8 Cards 90
- LINE LED Pattern 92
- Installation Manual 93 93
- 2.4.9 PRI30 Card 94
- 2.4.10 PRI23 Card 98
- Diameter Maximum Distance 100
- 0.5 mm: Under 200 m 100
- 2.4.11 IP-GW4 Card 101
- LED Indications 102
- 2.4.12 IP-GW4E Card 103
- 2.4.13 IP-GW16 Card 105
- 2.5.1 CSIF4 and CSIF8 Card 107
- Pin Assignments 108
- 2.5.2 DHLC8 Card 109
- 2.5.3 DLC8 Card 112
- 2.5.4 DLC16 Card 114
- 2.5.5 SLC8 Card 116
- 2.5.6 EXT-CID Card 118
- 2.5.7 SLC16 and MSLC16 Cards 119
- 2.5.8 IP-EXT16 Card 121
- 2.6.1 OPB3 Card 123
- 2.6.2 DPH4 Card 124
- 2.6.3 DPH2 Card 126
- Doorphone 2 128
- Doorphone 1 128
- 2.6.4 EIO4 Card 129
- Installation Manual 131 131
- 2.6.5 ECHO16 Card 132
- 2.6.6 MSG4 Card 133
- 2.6.7 CTI-LINK Card 134
- 2.7 Connection of Extensions 136
- With APT 137
- With DPT 137
- Using an EXtra Device Port 138
- Using a Modular T-Adaptor 139
- With KX-T7600E Series DPT 141
- Connecting to a Master DPT 143
- 2.8.1 Overview 145
- 146 Installation Manual 146
- 2.8.2 Procedure Overview 147
- 4. Finish the site survey 148
- 6. Mount the CS on the wall 148
- 2.8.3 Site Planning 149
- 150 Installation Manual 150
- CS Coverage Area 151
- Site Survey Preparation 151
- 152 Installation Manual 152
- 2.8.4 Before Site Survey 153
- CS No. CS ID No 154
- Channel Number Switch 155
- Radio Signal 155
- Test Switch 155
- Channel 0 155
- 156 Installation Manual 156
- Channel No 157
- 158 Installation Manual 158
- 5 m to 10 m 159
- Channel no. 0 Channel no. 1 159
- Channel no. 2 Channel no. 3 159
- Clearing the Stored Scan Data 160
- 2.8.6 After Site Survey 161
- Using a CSIF Card 162
- Using a DHLC/DLC Card 163
- Connecting the CS 164
- To CSIF card 165
- Registering the PS 166
- Installation Manual 167 167
- PIN for PS Registration 168
- PS Termination 169
- Testing the Operation 170
- 2.8.8 Wall Mounting 171
- Reference for Wall Mounting 172
- 2.9.1 Overview 173
- 174 Installation Manual 174
- 2.9.2 Procedure Overview 175
- 2.9.3 Site Planning 177
- 178 Installation Manual 178
- 180 Installation Manual 180
- 2.9.4 Before Site Survey 181
- 182 Installation Manual 182
- 2.9.5 Site Survey 183
- 184 Installation Manual 184
- Scan Data No 185
- Deleting the Stored Scan Data 186
- 2.9.6 After Site Survey 187
- Extn. No 192
- System Lock Password 193
- 2.9.8 Wall Mounting 196
- Sensors, and External Relays 198
- Connection 199
- To doorphones/ 200
- Installation Manual 201 201
- PC/Printer (via RS-232C) 202
- Installation Manual 203 203
- Trunk Card 205
- (e.g., LCOT8) 205
- Extension Card 205
- (e.g., SLC8) 205
- 206 Installation Manual 206
- Using BRI Card 207
- 208 Installation Manual 208
- Installation Manual 209 209
- Installation Manual 211 211
- 212 Installation Manual 212
- Section 3 213
- 3.1 Overview 214
- 3.2 Connection 215
- External Modem Connection 216
- Password Security 217
- Items (Quick Setup) 218
- Installation Manual 219 219
- 220 Installation Manual 220
- Section 4 221
- Troubleshooting 221
- 4.1 Troubleshooting 222
- 4.1.2 Connection 224
- 4.1.3 Operation 226
- 4.1.4 Using the Reset Button 228
- Error Log Display Format 229
- List of Errors and Solutions 231
- Section 5 241
- Appendix 241
- 5.1 Revision History 242
- 5.1.2 Version 2.0 243
- Installation Manual 245 245
- 246 Installation Manual 246
- Installation Manual 247 247
- 248 Installation Manual 248
- Installation Manual 249 249
- Copyright: 250
- KK0103AH6094 250
Verwandte Produkte und Handbücher für Gateways / Controller D-Link KX-TDA100
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern