D-link DSL 2740B Bedienungsanleitung

DSL-2740B Wireless ADSL2+ Router User Guide September 2006 ESL2740BEUA1G

DSL-2740B Wireless ADSL Router User Guide ixInformation you will need about your DSL-2740B Wireless ADSL Router: Username This is the Username needed

90 DHCP CLIENTS window WLAN STATION This window displays authenticated wireless stations and their status.

91 WLAN STATION Window SYSTEM LOG The system log displays chronological event log data. The event log can be read from local host or sent to syslog

92 SYSTEM LOG window (1) 1. Click Configure System Log button to enter system log configuration window. 2. Click Enable radio button and select Lo

93 Log Level All events above or equal to the selected level will be logged. Display Level All logged events above or equal to the selected level w

94 SYSTEM LOG window (2)

95A Technical Specifications General Standards: ADSL Standards • ANSI T1.413 Issue 2 • ITU G.992.1 (G.dmt) AnnexA • ITU G.992.2 (G.lite) Annex

96 Physical and Environmental DC Inputs: Power Adapter: Input: 120V AC 60Hz Output: 12V AC, 1200mA Power Consumption: 12 Watts (max) Operating Tem

97 Wireless Modulation IEEE 802.11b: DQPSK, DBPSK, DSSS, and CCK IEEE 802.11g: BPSK, QPSK, 16QAM, 64QAM, OFDM Frequency 2400 ~ 2484.5MHz ISM band Ch

98B Configuring IP Settings on Your Computer In order to configure your system to receive IP settings from the Router it must first have the TCP/IP

99 3. In the Network and Internet Connections window, click Network Connections. 4. In the Network Connections window, right-click on Local Area

DSL-2740B Wireless ADSL Router User Guide 11 Introduction This section provides a brief description of the Router, its associated technologies, and a

1005. In the General tab of the Local Area Connection Properties window, highlight Internet Protocol (TCP/IP) under “This connection uses the follo

101Windows 2000 First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, click the Start button, point to Settin

102Windows 95 and Windows 98 First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, click the Start button, po

103Your computer is now ready to use the Router’s DHCP server. Windows NT 4.0 Workstations First, check for the IP protocol and, if necessary, insta

104C Low Pass Filters for DSL Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regul

105Three Port Filter Another style of filter is installed at the same point where the Router connects to the telephone line. Only a single filter i

DSL-2740B Wireless ADSL Router User Guide 2Router Features The DSL-2740B ADSL Router utilizes the latest ADSL enhancements to provide a reliable Inte

DSL-2740B Wireless ADSL Router User Guide 3Standards Compatibility and Compliance The DSL-2740B complies with or is compatible with the following sta

DSL-2740B Wireless ADSL Router User Guide 4Front Panel Display Place the Router in a location that permits an easy view of the LED indicators on the

DSL-2740B Wireless ADSL Router User Guide 5Rear Panel Connections All cable connections to the Router are made at the rear panel. Connect the power a

DSL-2740B Wireless ADSL Router User Guide 6Setting Up a Wireless Network In order to get the best performance from the wireless component of the Rout

DSL-2740B Wireless ADSL Router User Guide 7Location and Wireless Operation Many physical environmental factors can impact wireless networks. Radio wa

DSL-2740B Wireless ADSL Router User Guide 82 Hardware Installation The DSL-2740B Wireless ADSL Router maintains three separate interfaces, an Etherne

DSL-2740B Wireless ADSL Router User Guide 9Network Connections Wired network connections are provided through the ADSL port and the four Ethernet po

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

DSL-2740B Wireless ADSL Router User Guide 10Computer to Router Connection You can connect the Router directly to a 10/100BASE-TX Ethern

DSL-2740B Wireless ADSL Router User Guide 11The illustration below shows the DSL-2740B connected to Ethernet LAN devices, Wireless LAN devices, and t

DSL-2740B Wireless ADSL Router User Guide 123 Basic Router Configuration The first time you set up the Router it is recommended that you configure th

DSL-2740B Wireless ADSL Router User Guide 13Access the Configuration Manager In order to make sure your computer’s IP settings allow it to communicat

DSL-2740B Wireless ADSL Router User Guide 14Configure the Router When you successfully connect to the web manager, the Home directory tab will displa

DSL-2740B Wireless ADSL Router User Guide 15All configuration and management of the Router is done using the web-based management interface pictured

DSL-2740B Wireless ADSL Router User Guide 16 Click Next to go to the next Setup Wizard window. Using the Setup Wizard – WAN Settings - Choose Co

DSL-2740B Wireless ADSL Router User Guide 17

DSL-2740B Wireless ADSL Router User Guide 18Using the Setup Wizard - For PPPoE/PPPoA connection: 1. Select the specific Connection Type and Encapsu

DSL-2740B Wireless ADSL Router User Guide 19Additional configurations available for PPP connection: PPP Connection Parameters Description Dial on de

Table Of Contents BEFORE YOU START ... V Install

DSL-2740B Wireless ADSL Router User Guide 20Using the Setup Wizard - For Dynamic IP (1483 Bridge) connection: 1. Select the specific Connection Type

DSL-2740B Wireless ADSL Router User Guide 21Using the Setup Wizard - For Static IP Address (1483 Bridge) connection: 1. Select the specific Connecti

DSL-2740B Wireless ADSL Router User Guide 22 Using the Setup Wizard - For Static IP Address (IPoA) connection: 5. Select the specific Connection Typ

DSL-2740B Wireless ADSL Router User Guide 23Using the Setup Wizard - For Bridge Mode connections: 1. Select the specific Connection Type and Encapsu

DSL-2740B Wireless ADSL Router User Guide 24Using the Setup Wizard - For LAN Settings: You can configure the LAN IP address to suit your preference.

DSL-2740B Wireless ADSL Router User Guide 25Using the Setup Wizard - For Wireless LAN Settings: 1. Click the Enable Wireless box to allow the router

DSL-2740B Wireless ADSL Router User Guide 26Using the Setup Wizard - Finish and Restart Finally you can confirm that the setup process is completed.

DSL-2740B Wireless ADSL Router User Guide 27ADSL To access the ADSL (WAN) Settings window, click on the ADSL link button on the left side of the firs

DSL-2740B Wireless ADSL Router User Guide 28ADSL Settings Window Additional information for you to help you configure your WAN connections: ATM Se

DSL-2740B Wireless ADSL Router User Guide 29by bursts of packets at variable intervals, and some moderate packet loss and delay is acceptable. This c

VIRTUAL SERVER ...50 PORT TRIGGERING ...

DSL-2740B Wireless ADSL Router User Guide 30WLAN To access the WLAN Settings window, click on the WLAN link button on the left side of the first wind

DSL-2740B Wireless ADSL Router User Guide 31The SSID identifies members of the Service Set. Accept the default name or change it to something else. I

DSL-2740B Wireless ADSL Router User Guide 32 LAN Settings Window To change the LAN IP Address or Subnet Mask, type in the desired values and click th

DSL-2740B Wireless ADSL Router User Guide 33Parameters Description UPnP UPnP supports zero-configuration networking and automatic discovery for man

34DNS The Router can be configured to relay DNS settings from your ISP or another available service to workstations on your LAN. When using DNS rel

35 When you have configured the DNS settings as desired, click the Save Settings button.

364 Advanced Router Management Directory Configuration and Read-only Windows Setup Click the Setup tab to access the Wizard, ADSL Settings, W

37Route, ARP, DHCP Clients, WLAN Station, and System Log. ADVANCED ADSL The ADSL Configuration window allows the user to set the configuration for

38ADVANCED WLAN ADVANCED WLAN page allows you to tweek more advanced wireless settings. Most users will do just fine using default settings. ADVAN

39Channel Operation channel of your access point. Channel availability is different for different countries due to their regulation. 802.11 Mode Se

TECHNICAL SPECIFICATIONS ...95 CONFIGURING IP SETTINGS ON YOUR C

405. Click the Save Settings button to apply settings. WLAN SECURITY Window – WEP Notice If encryption of any kind, at any level is applied to t

411. Select 802.1x from the Network Authentication drop-down list. 2. Enter your RADIUS server data: IP Address, Port, and Key. 3. Configure WE

42 WLAN Security Window – WPA-PSK WPA (Wi-Fi Protected Access) Wi-Fi Protected Access was designed to provide improved data encryption, perceived a

434. Click Save Settings to apply your settings. WLAN Security Window – WPA WLAN Filter The WLAN Filter is used to control wireless client devices

44 WLAN FILTER Window WLAN BRIDGE Wireless bridge is used to bridge AP traffic between other APs. You can select Wireless Bridge (also known as Wi

45 Notice Wlreless Bridge function is available only when 802.11n is disabled. Please go to ADVANCED WLAN page to disable 802.11n before configuring

46WLAN QOS WLAN QoS (Quality of Service), also called WMM (Wi-Fi Multi-media), is used to prioritize the wireless packets when you are using wireles

47 WLAN QoS Window (1) 4. Enter the name of the rule. 5. Select priority from the Wireless Transmit Priority drop-down list (1~4, higher number ha

48 WLAN QoS Window (2) FIREWALL The Firewall Configuration window allows the Router to enforce specific predefined policies intended to protect aga

49traffic, attempts to disrupt connections between two machines, thereby preventing access to a service, attempts to prevent a particular individual

DSL-2740B Wireless ADSL Router User Guide vAbout This User Guide This user’s guide provides instructions on how to install the DSL-2740B Wireless ADS

50VIRTUAL SERVER Use the Virtual Server window to set up single-port or static-port range forwarding rules applied to inbound (WAN-to-LAN) traffic.

51VIRTUAL SERVER window 1. Click the Add A Rule button to enter your virtual server configuration window. 2. Select a service from the drop down l

52 PORT TRIGGERING Window Configure these parameters for port triggering on the router: Virtual Server Category Description Trigger Port Start/End

53Open Protocol Opened protocol for remote users DMZ Since some applications are not compatible with NAT, the Router supports use of a DMZ IP addr

54To designate a DMZ IP address, type in the IP Address of the server or device on your LAN in the DMZ Host IP Address box, and click the Save Setti

55 OUTGOING IP FILTER Window Note If more than one criterion is configured, all of them must be matched for this outgoing filter rule to take effe

56 INCOMING IP FILTER By default, all incoming packets are blocked if Firewall is enabled. But you can allow specific type of packets to be accepted

57 INCOMING IP FILTER Window BRIDGE FILTER Bridge filters are used to block or allow various types of packets through the WAN interface. This may b

581. Click Chnage Policy button to change bridge filter policy between Forwarded and Blocked. 2. Click the Add A Rule button to enter your bridge

59 PARENT CONTROL Parent control is used to prevent specific local hosts from accessing Internet based on their MAC address. 1. Click the Add A Ru

DSL-2740B Wireless ADSL Router User Guide viPacking List Open the shipping carton and carefully remove all items. Make sure that you have the items l

60PARENT CONTROL Window URL FILTER URL filter is used to control Internet website access. You can decide that your local hosts can access these sp

61 URL FILTER Window QUALITY OF SERVICE QoS (Quality of Service) is a traffic class rule to classify the upstream traffic, assign queuing priority a

622. Enter the name of the rule. 3. Assign ATM priority from the Assign ATM Transmit Priority drop-down list. 4. Check Enable Differentiated Ser

63 All of the specified conditions in this classification rule must be satisfied for the rule to take effect. To delete the configured QoS rule, ch

64 ROUTING Window RIP The Router supports RIP v1 and RIP v2 used to share routing tables with other Layer 3 routing devices on your local network o

653. Check Enabled box and click Save Settings to apply your settings. To disable RIP, click Disabled radio button and click Save Settings. RIP

66Interface The interface which RIP function is applied. Version RIP has two versions available: RIP 1 and RIP 2. RIP 1 uses classed routing tabl

67 PORT MAPPING Window (1) 2. Click Add button to enter port mapping configuration window. 3. Enter the group name and select the specific interf

68 PORT MAPPING Window (2)

69TOOLS Click the Tools tab to reveal the window buttons for various functions located in this directory. The Diagnostics window is the first item i

DSL-2740B Wireless ADSL Router User Guide viiSecurity for wireless communication can be accomplished in a number of ways. The DSL-2740B supports WPA

70BACKUP SETTINGS Once you have configured the Router to your satisfaction, it is a good idea to back up the configuration file to your computer. To

71 UPDATE SETTINGS To load a previously saved configuration file, click the Browse button and locate the file on your computer. Click the Update Set

72 RESTORE DEFAULT Window TR069 CLIENT TR-069 is a WAN Management Protocol which allows an Auto-Configuration Server (ACS) to perform auto-configur

733. Click Save/Apply to apply your settings. TR-069 CLIENT Window SNMP CONFIGURATION Simple Network Management Protocol is a standard for intern

743. Click Save/Apply to apply your settings. SNMP CONFIGURATION Window DDNS The Router supports DDNS (Dynamic Domain Name Service). The Dynamic

75specific host on the LAN using standard DNS. If for example you are running a public web server or VPN server on your LAN, this ensures that the h

76Configure these parameters for DDNS: DDNS Parameters Description DDNS Server Select one of the DDNS registration organizations form those listed

77 TIME Window ACCESS SERVICE You can select to enable or disable of which management services from being used in your router, for LAN and/or WAN

782. Click the Save/Apply button to apply your settings. CAUTION: If you disable HTTP service, you’ll not be able to access the router’s config

79ACCESS IP The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Co

DSL-2740B Wireless ADSL Router User Guide viiiRouter, you may choose among the numerous options available on the Modulation Type drop-down menu on th

80ACCESS IP Window PASSWORD Access to your router is controlled through three user accounts: admin, support, and user. The user name admin has unres

81UPDATE FIRMWARE Use the Firmware Upgrade window to load the latest firmware for the device. Note that the device configuration settings may return

82 SAVE / REBOOT Window

83STATUS Use these windows to view system information and monitor performance. DEVICE INFO Use the Device Information window to quickly view basic

84ADSL This window displays ADSL information including Link Rate, SNR, and some Error Counters. ADSL Window LAN This window displays LAN informati

85 LAN Window WAN This window displays WAN information including IP address, Mask, Dafault Gateway, Primary/Secondary DNS Server.

86 WAN Window ATM This window displays ATM information including Cell Count and someError Counters.

87 ATM Window ROUTE This window displays the Routing Table of the router.

88 ROUTE Window ARP This window displays ARP Table of the router’s LAN port.

89 ARP Window DHCP CLIENTS This window displays all the client devices which have obtained IP addresses from the router.